How To Remove Throttle Cable From Atv Carb

More Answers On how to remove throttle cable from atv carb

How do you remove a throttle cable from a carburetor ATV?

How do you remove a throttle cable from a carburetor ATV? To remove the throttle cable, first pull the rubber on the cable. Then unscrew the locknut, which is closest to the carburetor, from the throttle cable. The locknut is attached to the tubular L – shaped fitting which comes out of the triangular cover on the brake side of the quad.

Removing throttle cable from carb | Polaris ATV Forum

Take the side cover off. Open the throttle fully by hand so the cable is loose. There is a slotted brass piece that traps the end of the cable. With the cable loose enough the brass piece comes out towards you and the cable slips out of the brass piece (don’t lose it). You can then unscrew the cable from the carb and pull it out.

How To Remove Throttle Cable From Carburetor? Detailed With Step-by …

Mar 23, 2022Step 3. Loosen the clamps screw of the carburetor. Now the throttle cable is visible. Pull back the rubber on the cable. Release the locknut which is set to the L-shaped tube. You have to notice which locknuts are the closest to the carburetor. The cable is attached to a gold or brass color plated plug. Step 4.

How to remove the throttle cable from the carb! | Raptor Forum

Turn the cable until the little ball on the end of it comes out of the plug. Do not lose the little plug, you will need it once your carb is back in. Simply pull the cable out of the tubular “L” shaped fitting and your done. Do the complete opposite to put it back together.

Removing the Throttle Cable from a Carb | Polaris ATV Forum

Discussion Starter · #1 · Jan 11, 2015. Only show this user. I have a 2005 Polaris Sportsman 500 ATV. I am removing the Carburetor for cleaning but can’t figure out how to remove the Throttle Cable from the Carb.Can anybody tell me how in a step by step manner. I have looked every where but can’t find anything on it.

Safest way to remove the throttle cable from the carburetor

How to remove the throttle cable from the carburetor First off, put off the fuel valve which is connected to the fuel tank. Carefully trace the fuel line all the way to the carburetor and take out the hose. Take a close look at the fuel line. If it’s worn out, make arrangements to replace it to prevent leakage in the future.

Removing throttle cable from carb? | The Dirt Bike | Motocross …

I cannot gather from your post the reason for replacing the cable however if the cable is still in tact you firstly need to get max play on cable, meaning turning adjuster near your throttle completely inwards (this helps alot as you want your inner cable to be as long as possible). I can gather you have already removed slide from carb so then …

How to get the throttle cable out of the carb cap?

For anyone else who reads this, if you are desperate, you can fabricate the OEM cap to work, but it is a bit cobbled. I cut the curved tube off the cap, and fought with it while I tried to drill or grind a little recess into the cap. The major problem is that the remnants of the curved tube will spin inside the cap while you try to drill.

250-500cc How to remove throttle cable from Mikuni Carb?

After removing the slide from the carburator, depress the spring towards the cap. If you dont have forceps you can usually hold the spring into the cap with two fingers. Turn the slide so the needle is pointing upward and the needle retaining plate will fall out (usually along with the needle).

Throttle cable removal 2004 Outty 400HO | Can-Am ATV Forum

Over50. ·. Registered. Joined Nov 2, 2010. ·. 227 Posts. #3 · Aug 13, 2011. Hi, 3 screws hold plate that cable goes into on the carb, under plate is a rubber O ring and you will see the cable wraped around the throttle shaft plate, push on thumb leaver for throttle to open shaft plate, when open enough hold moving plate with your finger and …

How to Remove Throttle Cable from Carburetor in Ten Easy Steps

Jun 3, 2021Remove the carburetor. You can now unscrew the locknut that is closest or directly in front of your carburetor. Unscrew this locknut away from the carburetor’s throttle cable. This locknut will be attached to a fitting that has a shape like an “L” and is tubular. The fitting emerges from a cover that is triangular and is on the side of the quad.

Throttle Cable Removal – Blue Traxx Forum

82 Posts. Discussion Starter · #1 · Dec 29, 2004. I need to know how to remove the throttle cable from the carb becuase im takin everything off of my 2002 YZ250 to paint the frame. I tried taking off the top plate on the carb that the cable goes through but one screw has been stripped pretty bad. Isnt there any other way to remove the …

Removing Throttle/Idle cable from Carb – V-Twin Forum

I aasume you have loosened all the tension on the cables. With this complete, you should be able to pull the brass ferrules out of the carb bracket easy. Pay attention which is which ,i.e accelerator vs return. (The return is the one with the spring on it.) Make certain you pay attention to the brake switch assembly. Install a small 1/8″ spacer …

How to remove throttle and choke cable from carb

I need to remove the throttle and choke from the carburetor so i can replace it i’m having trouble removing the screw at the bottem which i think is all i need to do before the cables will come out but the screw is stuck and i can’t get it out i want to make sure if i drill through the screw i won’t damage anything or maybe i dont have to take that screw at all

SOLVED: How do i disconnect the throttle from the carb on – Fixya

You can remove the plate (circled in pink) to expose cable. Once plate is removed, you can see (circled in yellow) where the throttle cable end locks into. Carefully manuever the cable to come out. Do whatever you need to do, and do the opposite to reinstall. Hope this helps and best of luck.

how to remove throttle cable from carb top? – ThumperTalk

Thanks MG, but I have the manual. the problem is the throttle cable is permanently connected to the carb top and any attempt to remove it breaks the carb top or the cables ability to glide smoothly. I honestly don’t think there’s even a trick to remove it. I just sent an email to Keihin and asked if there’s another top that would fit or if …

Removing throttle cable from carb – Yamaha 2 Stroke – ThumperTalk

From here the spring and plastic retainer will slide off of the cable, and then you can remove the throttle cable nut from the carb cap. Link to comment Share on other sites. More sharing options… Create an account or sign in to comment. You need to be a member in order to leave a comment. Reply with: Sign in with Google. Sign in with Facebook. Sign in with Twitter. Sign in with Microsoft …

How do I remove throttle cable? – Raptor Forum

If you can pull the quadrant towards the cable just a bit it will create slack in the cable, barely enough you can slide it over the runner/tunnel it rides in…or there is just enough room to fit a needle nose pliers to grab the cable and pull it towards the carbs to get enough slack to slide it over the quadrant.

Removing throttle cable – Suzuki Central Forum

I haven’t done this, but I would think you could unhook the cable from the thumb throttle and this may make it easier. Mine was easier once I turned my adjuster in all the way. If I remember correctly, I bent a little piece of wire so it had a hook on the end so I could hold the cable to pull it out easier. Good luck.

removing throttle assemble from carb | Kawasaki ATV Forum

Prairie 700 – I ended up just leaving it in and cleaning around it. I did end up breaking the little plastic “Y” which connects to the coolant filter line.

How to clean ATV carburetor without taking it off – Quad Bike Guide

Step 1: Get all your cleaning supplies together on your workbench. and compressed air (either air compressor or a can of compressed air). Step 2: Disconnect the carb from the bike. Most of the time, this is done by removing the cap, cable, and slide. There are also many hoses on the carb.

How do you remove the throttle cable from the carb on a 2004 Yamaha …

Screw the cable adjuster on the carburetor all the way in on the carburetor, where the cable attaches to the carburetor. Screw it on, so that there is slack in the cable clockwise. Manually open the throttle and hold it all the way open on the carb, with your finger, use a small pick to remove the cable end,from the carburetor throttle plate, then pull the cable out of the carburetor.

setting carb new throttle cable – Polaris ATV Forum – QUADCRAZY

i have a 95 polaris xplorer 400. just replaced the throttle cable. has oil inject cable as well. whats the procedure for adjusting the cable. start at the carb and adjust till the carb is wide open or start at the throttle adjuster on the bars. it seems to run ok and starts fine but now as soon as i hit the throttle hard it bogs and then catches up. im unsure of procedure.

ATV Throttle And Clutch Cable Maintenance – AtvHelper

There are usually a couple of nuts to loosen before you can remove the throttle cable from the throttle body. Then you can remove the throttle cable from the throttle lever up on the right side of the handle bars. This step is similar to removing the clutch cable from the clutch lever. There that’s it, now you can remove the cable from the ATV.

Choke cable removal??? | Blue Traxx Forum

One of the chokes is partially ON. You may lose the cable, but pull that sucker out. some penetrating oil may help. clean everything up before reassembly…i used a piece of dowel and some emery cloth to clean the choke bore…and used marine approved lubricant and no problems since then. plus ’broomstick’ the cable. pull it loose from the …

How To Remove Throttle Cable From Carburetor? Detailed With Step-by …

What you have to do is push the throttle bracket forward then slide the cable to your hand through the hole. You can also pry off a retaining clip with it. Using a screwdriver is also a good way to get the cable from the body. There is another way to disconnect the cable from the bracket. You can either press the tabs or shacking it.

How do I remove the throttle cable? | Polaris ATV Forum

there should be like a black cover you take off and the cable end should be underneath it. you have to turn the mechanism with your hand to loosen the cable to slide it out. Save Reply L loftgolf Registered Joined Apr 27, 2010 4 Posts Discussion Starter · #3 · Apr 29, 2010 We figured it out! Thank you for your response!

Removing throttle cable from carb? | The Dirt Bike | Motocross …

I cannot gather from your post the reason for replacing the cable however if the cable is still in tact you firstly need to get max play on cable, meaning turning adjuster near your throttle completely inwards (this helps alot as you want your inner cable to be as long as possible). I can gather you have already removed slide from carb so then …

Throttle Cable Removal – Blue Traxx Forum

82 Posts. Discussion Starter · #1 · Dec 29, 2004. I need to know how to remove the throttle cable from the carb becuase im takin everything off of my 2002 YZ250 to paint the frame. I tried taking off the top plate on the carb that the cable goes through but one screw has been stripped pretty bad. Isnt there any other way to remove the …

How do you remove the throttle cable from the carb on a 2004 Yamaha …

Screw the cable adjuster on the carburetor all the way in on the carburetor, where the cable attaches to the carburetor. Screw it on, so that there is slack in the cable clockwise.