Mr. Rooter’s Tip Of The Day: One of the easiest plumbing installations: Self piercing saddle valve for both copper and galvanized. Saddle valves allow you to tap into a water line without cutting the pipe and inserting a T-fitting.
Tip #1 When installing a saddle valve on galvanized pipe, shut off the water, drain the p [ipe, then drill a 3/16″ hole in the pipe. To keep the drill bit from sliding off, tape a small piece of wood to the surface.
When running a water supply tube to a new refrigerator ice maker, humidifier, or other appliance, you’ll need a way to tap into an existing water supply pipe. An easy way to do this on a copper pipe is by using a special fitting known as a saddle valve or needle valve.
An easy way to do this on a copper pipe is by using a special shutoff fitting known as a saddle valve or needle valve. The term saddle derives from the shape of the valve as it sits atop a water pipe; the term needle refers to the sharp, hollow needle inside the valve that punctures the water pipe after the valve is mounted.
How do you install a saddle valve on a galvanized pipe?
Use a stainless steel coupling if the galvanized pipe is in a damp position to avoid problems associated with rust. Unthreaded galvanized pipe connects together using a coupling. Connecting together galvanized pipes that are non-threaded uses a coupling that creates a sealed joint.
How do you connect galvanized pipes without threads?
Because saddle valves are not permanently attached, they are prone to leaks and can potentially cause extensive property damage when they ultimately leak. Saddle valves tend to reduce water flow, causing them to become clogged and leak. Extensive property damage could result from these leaks.
Are saddle valves safe?
A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then adding the small supply line leading to the appliance.
What is a saddle valve used for?
A saddle valve is a valve used to supply liquid where a low volume, low pressure stream is required. The name is derived from the fact that it is mounted in such a way that it “saddles” the line, mounting it from both sides.
Are saddle valves any good?
Most of them don’t leak, but they have a much higher chance of leaking than a properly installed water valve. My advice is to not use saddle valves. When installing an ice maker or whole-house humidifier, tap off of an existing water line with a proper tee fitting and have a proper shutoff valve installed.
Can you shut off a saddle valve?
After locating the saddle valve, turn off the water supply to the refrigerator by turning the saddle valve handle clockwise. You may get a little bit of water from the valve’s packing nut as you close it. If so, it should stop leaking once the valve is fully closed.
What can I use instead of a saddle valve?
A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then adding the small supply line leading to the appliance.
Are saddle valves OK?
Because saddle valves are not permanently attached, they are prone to leaks and can potentially cause extensive property damage when they ultimately leak. Saddle valves tend to reduce water flow, causing them to become clogged and leak. Extensive property damage could result from these leaks.
Can you replace a self piercing saddle valve?
To replace a saddle valve or tee off an existing water line, start by obtaining the needed parts. I’m assuming the saddle valve is connected to a ½” copper water line. If you’re comfortable soldering copper tubing and you already have the equipment to do it, this project will cost about $10.
How do you seal a saddle valve?
Remove the nut holding the tubing onto the valve. Wrap two wraps of tape around the threads on the valve in the direction of threads. Now screw on the cap and tighten until snug. Turn on house water, and open the saddle valve and check for leaks.
How do you remove a plumbing saddle valve?
Saddle valves are self-tapping devices. Once mounted on a line, with the included rubber seal in place, all that is required is to turn the valve clockwise until it pierces the water line. When the valve handle can no longer be turned, it is done tapping the pipe. Turning the handle counter-clockwise opens the valve.
Can you remove a saddle valve?
Because saddle valves are not permanently attached, they are prone to leaks and can potentially cause extensive property damage when they ultimately leak. Saddle valves tend to reduce water flow, causing them to become clogged and leak. Extensive property damage could result from these leaks.
More Answers On Can You Use A Saddle Valve On Galvanized Pipe
Installing A Saddle Valve: Copper & Galvanized Pipe – PRWeb
Tip #1 When installing a saddle valve on galvanized pipe, shut off the water, drain the p [ipe, then drill a 3/16″ hole in the pipe. To keep the drill bit from sliding off, tape a small piece of wood to the surface. Tip #2 Once you’ve drilled the hole, remove the piece of wood and clean off any burrs on the hole with a file.
Saddle valve on galvanized pipe | Terry Love Plumbing Advice & Remodel …
Aug 21, 2020If you are not going to get more involved with pipe changing, I would just replace the saddle stop valve. When installing on galvanized, you need to drill a hole. That hole should be there for the first one, but be prepared. Have the piercing needle extend into the hole while attaching to get the alignment right.
Replacing saddle valve on galvanized pipe – DIY Home Improvement Forum
Nov 10, 2020Install two new sections with a union. Of course you need to have access to the fittings at both ends of that pipe. Or leave it alone until you decide to repipe. Galvanized pipe is very old technology. PEX would be the current replacement. A cheap fix would be to remove the saddle valve and use a hose clamp and piece of rubber to cover the hole.
Question Why are saddle valves illegal? – Megan Ann Blog
How do you put a saddle valve on a galvanized pipe? Tip #1 Start by placing the rubber gasket on top of the pipe. Tip #2 Arrange the saddle-valve body over the rubber gasket with a bolt on each side. Tip #3 Assemble the nuts and bolts, finger tight. Tip #4 Make sure the position of the valve is correct, then tighten down the nuts with a wrench.
Can You Use A Saddle Valve On Galvanized Pipe | Oil Storage Tank
Can You Use A Saddle Valve On Galvanized Pipe. Questions › Can You Use A Saddle Valve On Galvanized Pipe. 0 Vote Up Vote Down. admin Staff asked 6 months ago. Email Name Website. Comment. Your Answer. Your Email. Your Name. Search for: Recent Posts. Oil and Gas Companies in Qatar List;
What Can I Use Instead Of A Saddle Valve? – All Answer You Need
Apr 10, 2022Will a saddle valve work on galvanized pipe? Tip #1 When installing a saddle valve on galvanized pipe, shut off the water, drain the p[ipe, then drill a 3/16″ hole in the pipe. One of the easiest plumbing installations: Self piercing saddle valves. The advantage of using a saddle valve on copper pipe is that it can be installed with the line …
Saddle valves: cheap, easy, and wrong – Structure Tech Home Inspections
To start, that’s a saddle valve pictured at right. These are devices that allow for a very fast, cheap, do-it-yourself installation of a ¼” water supply line, typically used to supply water to ice makers and whole-house humidifiers. Saddle valves are installed by tightening a metal clamp onto a water pipe, then tightening down a needle …
Drilling into Galvanized Pipe – DoItYourself.com Community Forums
Can I drill a hole in the galvanized pipe for the saddle valve? Upvote #2 04-03-09, 03:55 PM plumbermandan. Banned. Rule And/Or Policy Violation. Join Date: Jan 2009. Location: Texas. Posts: 896 Received 0 Votes on 0 Posts you could but why would you want to? it may be opening a can of worms depending on the pipes condition not to mention that …
Can I use a Saddle valve on PVC water pipe? | Terry Love Plumbing …
Throw the saddle valve in the trash and plumb the water line in right. You should put a shut off valve where you tap into the supply line, then reduce the size and adapt to the copper tubing. Saddle valves frequently develop leaks after being in use. The professional plumber on this venue all recommend against their use.
How to Install a Self-Piercing Saddle Valve – The Spruce
May 6, 2022Mount the Valve. Make sure the needle is completely retracted into the saddle valve before starting. Place the rubber washer or gasket on the underside of the top bracket of the saddle valve so its opening is directly aligned with the needle on the valve. Fit the top and bottom brackets of the saddle valve around the water supply pipe and hold …
Your Question What can I use instead of a saddle valve?
Saddle valves are against plumbing code now because they are prone to leaks. Leaks create corrosion to the rest of the plumbing system. Will a saddle valve work on galvanized pipe? When installing a saddle valve on galvanized pipe, shut off the water, drain the p[ipe, then drill a hole in the pipe.
Natural Gas Saddle Valves – InterNACHI®️ Forum
The saddle valve is dependent on drilling a smooth hole and buffing the area to which it is attached. If the pipe is a soft metal such as copper it can become deformed as you tighten the lock nuts on each side plus if one side is tighter then it is not balanced pressure which can invite leakage. P.s two different kinds of metal (figure the rest …
Can You Use Saddle Valve – ehorsegear.com
Nov 3, 2020A flexible copper, vinyl or stainless steel pipe is connected to the saddle valve and run to the back of the refrigerator. It will be either a 3/8-inch or a 1/4-inch pipe made of flexible copper, poly or stainless steel. Once you locate the supply line, follow it back until you find the saddle valve.
How To Remove A Saddle Valve (Step-by-Step Guide) – Upgraded Home
Step 1: Prepare the Necessary Tools. You’ll need more than a few tools to remove and replace a saddle valve. For removing the saddle valve itself, secure a pair of pliers and a pipe cutter. To replace the saddle valve, you’ll need a 1/2-inch copper tube, a 1/2-inch copper tee, and a push-fitting stop valve.
Saddle valve on galvanized pipe? – InterNACHI®️ Forum
We drilled a hole and installed the saddle valve. I never seen a saddle valve needle go threw steel pipe. I must say that I do not like these valves one bit. I don’t know how many I had to change because they wouldn’t shut the water off all the way when we worked on Humidifiers. I think a standard valve should be installed, especially when it …
Replace saddle valve on (apparently) galvanized pipe?
I’ve never done any plumbing work so if you say I need to cut pipes and sweat things, I’ll be doing a lot of YouTube-ing and probably 7 trips to Home Depot. Not averse to this! This looks like it’s actually a saddle valve on galvanized pipe, not copper, so most of my Googling on this is yikes.
What Can I Use Instead Of A Saddle Valve? – All Answer You Need
Will a saddle valve work on galvanized pipe? Tip #1 When installing a saddle valve on galvanized pipe, shut off the water, drain the p[ipe, then drill a 3/16″ hole in the pipe. One of the easiest plumbing installations: Self piercing saddle valves. The advantage of using a saddle valve on copper pipe is that it can be installed with the line …
Can You Use A Saddle Valve On Galvanized Pipe | Oil Storage Tank
Can You Use A Saddle Valve On Galvanized Pipe. Questions › Can You Use A Saddle Valve On Galvanized Pipe. 0 Vote Up Vote Down. admin Staff asked 6 months ago. Email Name Website. Comment. Your Answer. Your Email. Your Name. Search for: Recent Posts. Oil and Gas Companies in Qatar List;
Your Question What can I use instead of a saddle valve?
Saddle valves are against plumbing code now because they are prone to leaks. Leaks create corrosion to the rest of the plumbing system. Will a saddle valve work on galvanized pipe? When installing a saddle valve on galvanized pipe, shut off the water, drain the p[ipe, then drill a hole in the pipe.
Drilling into Galvanized Pipe – DoItYourself.com Community Forums
Can I drill a hole in the galvanized pipe for the saddle valve? Upvote #2 04-03-09, 03:55 PM plumbermandan. Banned. Rule And/Or Policy Violation. Join Date: Jan 2009. Location: Texas. Posts: 896 Received 0 Votes on 0 Posts you could but why would you want to? it may be opening a can of worms depending on the pipes condition not to mention that …
What You Need to Know About Galvanized Pipes – Whitt Inspections, LLC
Galvanized pipes are steel pipes dipped in a zinc coating. This practice (now referred to as galvanizing) came to be once we discovered that the typical lead piping leads to — you guessed it — lead poisoning. To correct over 70 years’ worth of municipal lead piping, city builders found galvanizing to be the easiest solution.
The 10 Most Common Plumbing Mistakes DIYers Make
Overtightening supply tubes, pipe and fittings and toilet bolts is the #1 DIYer mistake. If you crank too hard on a galvanized or black pipe, coupling, tee or elbow, you risk cracking the fitting. The crack may not happen right away, but the excessive force can break the fitting weeks later, causing a flood. Overtightening the plastic fittings …
Can I swap out a saddle valve? : Plumbing – reddit.com
Place the needle in the pre existing hole in the pipe and assemble the clamps that hold the valve to the pipe. Once you have it assembled, turn the new valve a couple of turns clockwise and then turn back the water on. Hopefully, it works out without leaks. 1. level 2.
Saddle tees and Clamp-It™ saddles – PlumbingSupply.com
We recommend the use of PVC glue and 2 each stainless steel hose clamps for each saddle tee. Note: Use a 61/64″ or 1″ (maximum) drill bit and drill a hole in the pipe to allow the saddle tee base outlet to fit into the pipe and flush fit the base against the pipe. Outlet socket sizes differ but all base outlets are the same size.
Pipe Saddle Weldable – uny.artebellezza.mo.it
Toll-Free: 800-68-VALVE (688-2583) 800-68-VALVE (688-2583) … Pipe Saddle is a contoured, integrally reinforced, butt-weld branch connection with a low stress intensification factor for low stresses and long fatigue life • Saddles may require notching when used with a U-bolt Smart Joint starts fusion machine and PE fittings production since …
Galvanized Pipe & Fittings at Lowes.com
Pipe Diameter: 1/2-in. Savings. Galvanized pipe is a steel pipe that’s been hot-dipped in zinc for a coating to provide strong resistance to corrosion. It’s commonly used for transporting compressed air, potable water, gasoline, oil, gases and more. Lowe’s carries a wide supply of galvanized steel pipes in a range of sizes to fit your project.
Can Galvanized Pipe Be Used For Natural Gas? – Upgraded Home
The International Fuel Gas Code (IFGC) allows galvanized pipes for natural gas delivery systems. The galvanized pipe must meet the standards outlined in ASTM A53/A53M-05. However, the IFGC is a model code. Jurisdictions having authority may change the code requirements. It is always advisable to check with your local building codes department …
is it possible to use a compression shut off on Galvanized 1/2″ pipe …
Retired Moderator. Joined Sep 18, 2009. 25,770 Posts. #2 · Apr 11, 2010. There are no compression shut off that will fit –sorry–You could remove the 1/2’ nipple and solder up a copper stub-out. Better be mighty important–that old iron could snap off inside the wall. New members: Adding your location to your profile helps in many ways.–M–.
Pipe Saddle Taps | McMaster-Carr
Also known as saddle valves, these self-piercing valves tap existing copper tubing lines so you can install a secondary water supply line to humidifiers, ice makers, and other equipment. Clamp the valve into position and turn the handle to pierce a 1/4 ” hole in the tubing. Do not use with pipe. The outlet connection is a 1/4 ” compression tube …
Natural Gas Saddle Valves – InterNACHI®️ Forum
The saddle valve is dependent on drilling a smooth hole and buffing the area to which it is attached. If the pipe is a soft metal such as copper it can become deformed as you tighten the lock nuts on each side plus if one side is tighter then it is not balanced pressure which can invite leakage. P.s two different kinds of metal (figure the rest …
Resource
https://www.prweb.com/releases/2012/6/prweb9591893.htm
https://terrylove.com/forums/index.php?threads/saddle-valve-on-galvanized-pipe.89340/
https://www.diychatroom.com/threads/replacing-saddle-valve-on-galvanized-pipe.705867/
https://meganannblog.com/question-why-are-saddle-valves-illegal/
https://www.oilstoragetank.org/question/can-you-use-a-saddle-valve-on-galvanized-pipe/
https://www.thatjamesmay.com/what-can-i-use-instead-of-a-saddle-valve/
https://structuretech.com/saddle-valves-cheap-easy-and-wrong/
https://www.doityourself.com/forum/plumbing-piping/385764-drilling-into-galvanized-pipe.html
https://terrylove.com/forums/index.php?threads/can-i-use-a-saddle-valve-on-pvc-water-pipe.3151/
https://www.thespruce.com/how-to-install-needle-saddle-valve-4125839
https://meganannblog.com/your-question-what-can-i-use-instead-of-a-saddle-valve/
https://forum.nachi.org/t/natural-gas-saddle-valves/74912
https://ehorsegear.com/post/can_you_use_saddle_valve
https://upgradedhome.com/how-to-remove-a-saddle-valve/
https://forum.nachi.org/t/saddle-valve-on-galvanized-pipe/174687
https://www.reddit.com/r/HomeImprovement/comments/f1h1h3/replace_saddle_valve_on_apparently_galvanized_pipe/
https://www.thatjamesmay.com/what-can-i-use-instead-of-a-saddle-valve/
https://www.oilstoragetank.org/question/can-you-use-a-saddle-valve-on-galvanized-pipe/
https://meganannblog.com/your-question-what-can-i-use-instead-of-a-saddle-valve/
https://www.doityourself.com/forum/plumbing-piping/385764-drilling-into-galvanized-pipe.html
https://www.whittinspections.com/homeowner-resources/galvanized-pipes/
https://www.familyhandyman.com/list/the-10-most-common-plumbing-mistakes-diyers-make/
https://www.reddit.com/r/Plumbing/comments/fe5imr/can_i_swap_out_a_saddle_valve/
https://www.plumbingsupply.com/saddle.html
https://uny.artebellezza.mo.it/Weldable_Pipe_Saddle.html
https://www.lowes.com/pl/Galvanized-pipe-fittings-Pipe-fittings-Plumbing/4294822020
https://upgradedhome.com/can-galvanized-pipe-be-used-for-natural-gas/
https://www.diychatroom.com/threads/is-it-possible-to-use-a-compression-shut-off-on-galvanized-1-2-pipe.68825/
https://www.mcmaster.com/pipe-saddle-taps
https://forum.nachi.org/t/natural-gas-saddle-valves/74912