PVC and brass pipe fittings use the same national pipe thread (NPT) connections. There are several ways to connect PVC pipe to brass pipe. Mechanical pipe connections using threaded joints are the most secure. Compression pipe connectors using rubber seals and locking nuts are the next best solution.
Also known generically as PTFE tape, it’s generally used as a sealant and lubricating material, perfect for installing fittings in the kitchen and bathroom. In fact, it’s essential to use thread tape for those household brass fittings unless a rubber seal or gasket is in place.
A part of the suggested span transcript after expanded is Changes the metal is going to expand and contract and the plastic is going to expand and contract. But they don't do it exactly the same amount.
Do use a sealant. Teflon tape, Teflon paste and pipe dope is intended for metal pipe and fittings. Metal to metal fitting joints are more difficult to tighten than plastic; the surfaces tend to gall without the aid of such lubricants as Teflon or pipe dope. Plastic fittings do not need this lubrication.
Connection. Slide the coupling over the end of the brass pipe so that the it reaches halfway through, then slide the PVC into the other end of the coupling. Tighten the clamp on both sides of the coupling with a screwdriver to secure the connection.
PVC and brass pipe fittings use the same national pipe thread (NPT) connections. There are several ways to connect PVC pipe to brass pipe. Mechanical pipe connections using threaded joints are the most secure. Compression pipe connectors using rubber seals and locking nuts are the next best solution.
Do you use Teflon tape on PVC to brass?
Also known generically as PTFE tape, it’s generally used as a sealant and lubricating material, perfect for installing fittings in the kitchen and bathroom. In fact, it’s essential to use thread tape for those household brass fittings unless a rubber seal or gasket is in place.
Can you thread brass into plastic?
When making threaded joints you need to use a sealer/lubricant. This is a product that helps seal the joint and also serves as a lubricant to make it easier to screw the male end into the female. The standard products for this are either Teflon pipe dope, Teflon tape, or PTFE tape.
Do I need Teflon tape on PVC to metal?
Do use a sealant. Teflon tape, Teflon paste and pipe dope is intended for metal pipe and fittings. Metal to metal fitting joints are more difficult to tighten than plastic; the surfaces tend to gall without the aid of such lubricants as Teflon or pipe dope. Plastic fittings do not need this lubrication.
How do you seal brass to PVC?
PVC is usually kept hidden, while brass is often showcased. Still, they can be connected should the need arise. And connecting PVC to brass plumbing is a task well within the reach of any competent do-it-yourselfer. It requires only minimal plumbing skills and some basic tools and materials.
Can you thread brass to PVC?
When making threaded joints you need to use a sealer/lubricant. This is a product that helps seal the joint and also serves as a lubricant to make it easier to screw the male end into the female. The standard products for this are either Teflon pipe dope, Teflon tape, or PTFE tape.
Can you use brass fittings on plastic?
PVC and brass plumbing couldn’t be more different. PVC is a relatively inexpensive, lightweight vinyl product, while brass is a dark, rich metal. PVC is usually kept hidden, while brass is often showcased. Still, they can be connected should the need arise.
Do you Teflon brass to plastic?
Do use a sealant. Teflon tape, Teflon paste and pipe dope is intended for metal pipe and fittings. Metal to metal fitting joints are more difficult to tighten than plastic; the surfaces tend to gall without the aid of such lubricants as Teflon or pipe dope. Plastic fittings do not need this lubrication.
Can you screw metal and plastic together?
To be able to thread plastic and metal fittings together the male fitting has to be plastic and the female fitting has to be metal. When fittings with a tapered thread such as NPT are tightened the male fitting is compressed and the female fitting is stretched (tensile stress).
How do you seal PVC thread to metal?
When making threaded joints you need to use a sealer/lubricant. This is a product that helps seal the joint and also serves as a lubricant to make it easier to screw the male end into the female. The standard products for this are either Teflon pipe dope, Teflon tape, or PTFE tape.
Do I need Teflon tape for PVC to brass?
Also known generically as PTFE tape, it’s generally used as a sealant and lubricating material, perfect for installing fittings in the kitchen and bathroom. In fact, it’s essential to use thread tape for those household brass fittings unless a rubber seal or gasket is in place.
Should you put Teflon tape on PVC fittings?
The right way to assemble a threaded PVC joint-Schedule 40 or 80 is finger tight plus one to two turns-no more. Two turns past finger tight plus the stress of the system pressure is within the tensile strength of one-inch PVC. Don’t use Teflon tape, Teflon paste or pipe dope. Do use a sealant.
Can you connect PVC to metal pipe?
When transitioning to PVC or CPVC piping, it’s best to do so at an elbow, tee or coupling with a female connection. Bluefrog technicians then use male plastic adapters to connect the PVC to the existing metal. Female slip adapters often crack when pressure is applied to seal the connection.
Can you thread PVC into brass?
PVC is usually kept hidden, while brass is often showcased. Still, they can be connected should the need arise. And connecting PVC to brass plumbing is a task well within the reach of any competent do-it-yourselfer. It requires only minimal plumbing skills and some basic tools and materials.
Should you use Teflon tape on brass to PVC?
The right way to assemble a threaded PVC joint-Schedule 40 or 80 is finger tight plus one to two turns-no more. Two turns past finger tight plus the stress of the system pressure is within the tensile strength of one-inch PVC. ([1,788 psi x 2] + 2,000 psi = 5,576 psi). Don’t use Teflon tape, Teflon paste or pipe dope.
Can I use brass fittings on plastic?
PVC and brass plumbing couldn’t be more different. PVC is a relatively inexpensive, lightweight vinyl product, while brass is a dark, rich metal. PVC is usually kept hidden, while brass is often showcased. Still, they can be connected should the need arise.
Can I use metal fittings on plastic pipe?
To be able to thread plastic and metal fittings together the male fitting has to be plastic and the female fitting has to be metal. When fittings with a tapered thread such as NPT are tightened the male fitting is compressed and the female fitting is stretched (tensile stress).
More Answers On Can You Thread Pvc To Brass
Can you thread PVC to brass? – FindAnyAnswer.com
4.6/5 (4,765 Views . 43 Votes) you can glue a PVC fitting that has either male or female iron pipe thread on the other end, from there you can screw on a brass fitting that also has iron pipe thread. DO NOT waste your time with thread tape, it simply won’t seal on PVC to metal, or PVC to PVC pipe thread fittings. Use thread dope instead.
Can you attach PVC to brass? – FindAnyAnswer.com
you can glue a PVC fitting that has either male or female iron pipe thread on the other end, from there you can screw on a brass fitting that also has iron pipe thread. DO NOT waste your time with thread tape, it simply won’t seal on PVC to metal, or PVC to PVC pipe thread fittings. Use thread dope instead.
Can I connect brass to PVC? – AskingLot.com
you can glue a PVC fitting that has either male or female iron pipe thread on the other end, from there you can screw on a brass fitting that also has iron pipe thread. DO NOT waste your time with thread tape, it simply won’t seal on PVC to metal, or PVC to PVC pipe thread fittings. Use thread dope instead.
threaded pvc to female brass. What should I use on threads?
Poly pipe fitting is connecting to PVC on one end and Brass on the other at yard hydrant. So, sound like you are saying to use the thread sealant on all and if leaking, then use Teflon tape and thread sealant. I planned to just put thread sealant on the male fittings. – Dean Jul 23, 2021 at 0:42 Add a comment Your Answer Post Your Answer
How to Connect PVC to Brass Plumbing | Home Guides | SF Gate
Apply a thin coat of plumber’s grease, about 1 inch wide, around the end of each pipe. Connection Slide the coupling over the end of the brass pipe so that the it reaches halfway through, then…
Can you glue PVC to brass? – AskingLot.com
Can you glue PVC to brass? you can glue a PVC fitting that has either male or female iron pipe thread on the other end, from there you can screw on a brass fitting that also has iron pipe thread. DO NOT waste your time with thread tape, it simply won’t seal on PVC to metal, or PVC to PVC pipe thread fittings. Use thread dope instead.
Can you thread brass into PVC? – AskingLot.com
you can glue a PVC fitting that has either male or female iron pipe thread on the other end, from there you can screw on a brass fitting that also has iron pipe thread. DO NOT waste your time with thread tape, it simply won’t seal on PVC to metal, or PVC to PVC pipe thread fittings. Use thread dope instead. Click to see full answer.
Proper way to join PVC pipes to brass ball valve
This is the standard method of attaching PVC pipe to threaded fittings. More turns and less tape. Pipe threads are tapered, in my experience 1-2 turns past hand tight is not nearly enough (and I generally only use 3 turns of Teflon tape). Make sure that your brass ball valve is not cracked, brass is fairly soft and I have seen the threaded part …
Sealing PVC Threads into Brass Valve – DIY Home Improvement Forum
To make the connection, I used male threaded PVC adapters. So it was male PVC threads into female brass. I coated the PVC threads with Rectorseal Tplus2 Pipe Thread Sealant, tightened them as tight as I could by hand then turned them another 1.5 turn into the brass valves with a wrench.
PVC to brass – Terry Love Plumbing Advice & Remodel DIY & Professional …
Reliability is much better if you can configure it to use a male pvc fitting into a female brass one. WHen you tighten the two together, the brass can handle the squeeze, the plastic in the female fitting just expands and could eventually split. SO, don’t overdo it and change if you can to put a male into brass. mliu jimbo Plumber Messages 8,922
How to Connect PVC Pipe to Brass Pipe | eHow
Connect a female adaptor on the PVC pipe with primer and glue. Wrap the threads of the brass pipe with Teflon thread tape several times. Screw the two together by hand. Hold the brass pipe with a wrench, and with another wrench tighten the PVC fitting on the brass pipe. Step 2 Slide one compression nut on the PVC pipe and one on the brass pipe.
How do you connect PVC to brass fittings? – askinglot.com
Connect a female adaptor on the PVC pipe with primer and glue. Wrap the threads of the brass pipe with Teflon thread tape several times. Screw the two together by hand. Hold the brass pipe with a wrench, and with another wrench tighten the PVC fitting on the brass pipe. Beside above, how do you connect a PVC pipe to a faucet?
Properly Connecting PVC Pipes to Brass Pipes In Any Situation
If you decide to go the route of threaded joints, you’ll want to attach a PVC male threaded fitting to a threaded brass fitting or else you may notice dripping once your connection is put to use. Detroit Nipple Works carries all the pipes, couplings, or fittings you’ll need to tackle this job yourself.
Can you thread plastic and metal NPT fittings together?
Can you thread plastic and metal NPT fittings together? To be able to thread plastic and metal fittings together the male fitting has to be plastic and the female fitting has to be metal. When fittings with a tapered thread such as NPT are tightened the male fitting is compressed and the female fitting is stretched (tensile stress).
Removing PVC threads from brass threads – DoItYourself.com
Received 9 Votes on 8 Posts. Glue serves no purpose on connections between pvc and brass, so that was overkill. It would be cheaper to replace the footvalve than to mess with chipping out the glue and pvc. You stand a chance of messing up the threads anyway, so a new one won’t hurt. Once a pvc fitting has been glued it will not come apart, and …
PVC to Brass connection – Plbg.com
Whenever I make a PVC (threaded) connection to a Brass pipe and wrap the brass thread end with teflon tape there seems to always be a slight “drip” at the PVC joint. I plan to redo the connection by breaking old joint, install new PVC elbow (3/4″ to brass nipple, wrap teflon tape on brass threaded end, then apply “Wet/Dry” PVC glue
joining pvc sch40 to copper or brass | Lawn Care Forum – LawnSite
Thread male plastic into female metal and never the other way around. So your PVC piece will be a male adapter, and your copper/brass/galvi piece will be a female adapter, or any other sort of female threaded fitting.
The “Do’s and Don’ts” of Assembling Threaded PVC Fittings
Here are some of the Do’s and Don’ts of PVC joint assembly. Don’t over-tighten joints by giving them “one more turn to be sure.” Do finger tighten plus one or two turns- No More. Don’t wrap Teflon …
Connecting Metal Threads to Plastic Threads – PVC
These composite unions are available with either female threads on the metal side or male threads on the metal side, and we also supply them with stainless steel rather than brass. If price is a significant factor, rather than using a standard PVC threaded fitting and screwing it directly onto the metal fitting, we supply threaded fittings which have a reinforcing ring around the outside.
Can you connect CPVC to brass? – AskingLot.com
Can you connect CPVC to brass? A male CPVC into a female brass fitting cannot expand, but it can snap off since the process of threading it removes a lot of the material needed for its strength. The brass thread CPVC adapter is the best way to do it. in mass, you can not connect plastic water pipe directly to a hot water tank.
What thread sealant to use with PVC fittings! – LinkedIn
When assembling threaded PVC fittings, a sealing compound that is non-hardening is the best. Recommended good practice is to use a thread sealant (not a thread lubricant) to assemble the joint to …
sealing a threaded brass to CPVC connection? – NastyZ28.com
The shower valve is threaded brass (male). I tried using a fitting similar to this (glue on CPVC on one end, threaded brass on the other): I gave the shower fitting several wraps with teflon tape, wrapping the threads against the direction of rotation. Then, I tightened the heck out of it, and glued everything up.
PVC Male – Brass Female Coupling – Terry Love
Oct 17, 2015. #2. I doesn’t look out of the ordinary. Some valves have a short thread. – Turn off the water. – Remove the rest of the PVC male thread out of the shut off valve, without damaging the thread. – Install a new male adapter. Use tape only, no plumber’s dope. – Cut the PVC pipe, install a coupling and finish to the valve with a piece …
How to Connect CPVC to a Brass Shower Valve – SF Gate
4. Connect the CPVC water pipe to the CPVC slip connection with CPVC cement. To get a good bond, sand the end of the pipe after you cut it with 120-grit wet/dry sandpaper and make a slight bevel.
Assembling Threaded Plastic Fittings | LASCO Fittings
The right way to assemble a threaded PVC joint-Schedule 40 or 80 is finger tight plus one to two turns-no more. Two turns past finger tight plus the stress of the system pressure is within the tensile strength of one-inch PVC. ( [1,788 psi x 2] + 2,000 psi = 5,576 psi). Don’t use Teflon tape, Teflon paste or pipe dope.
Can you glue PVC to brass? – Answers
You can not glue brass directly to PVC pipe. Use male/female adapters to join these two materials. ie, a male threaded PVC end fitting glued to the PVC pipe and a female threaded brass fitting …
joining pvc sch40 to copper or brass | Lawn Care Forum – LawnSite
Joined Jan 28, 2006. ·. 49 Posts. #4 · Apr 8, 2006. Only show this user. Dirty Water said: Thread male plastic into female metal and never the other way around. So your PVC piece will be a male adapter, and your copper/brass/galvi piece will be a female adapter, or any other sort of female threaded fitting.
GF Piping Systems PVC to Brass Transition Pipe Fitting, Adapter …
PVC spigot on one end and brass threads on the other for strength, resistance to corrosion, and for connecting plastic to metal fittings ; Maximum operating temperature of 140 degrees F ; Meets ASTM D1784 standards for quality assurance, and meets NSF standard 61 for potable water service ; Product Specifications . Ean : 7436829242094 : Exterior Finish: Brass : Item Weight: 7.2 ounces …
The “Do’s and Don’ts” of Assembling Threaded PVC Fittings
Here are some of the Do’s and Don’ts of PVC joint assembly. Don’t over-tighten joints by giving them “one more turn to be sure.” Do finger tighten plus one or two turns- No More. Don’t wrap Teflon …
Connecting Metal Threads to Plastic Threads – PVC
These composite unions are available with either female threads on the metal side or male threads on the metal side, and we also supply them with stainless steel rather than brass. If price is a significant factor, rather than using a standard PVC threaded fitting and screwing it directly onto the metal fitting, we supply threaded fittings which have a reinforcing ring around the outside.
Resource
https://findanyanswer.com/can-you-thread-pvc-to-brass
https://findanyanswer.com/can-you-attach-pvc-to-brass
https://askinglot.com/can-i-connect-brass-to-pvc
https://diy.stackexchange.com/questions/229107/threaded-pvc-to-female-brass-what-should-i-use-on-threads
https://homeguides.sfgate.com/connect-pvc-brass-plumbing-26699.html
https://askinglot.com/can-you-glue-pvc-to-brass
https://askinglot.com/can-you-thread-brass-into-pvc
https://diy.stackexchange.com/questions/46936/proper-way-to-join-pvc-pipes-to-brass-ball-valve
https://www.diychatroom.com/threads/sealing-pvc-threads-into-brass-valve.712279/
https://terrylove.com/forums/index.php?threads/pvc-to-brass.21640/
https://www.ehow.com/how_6639673_connect-pvc-pipe-brass-pipe.html
https://askinglot.com/how-do-you-connect-pvc-to-brass-fittings
https://www.detroitnippleworks.com/properly-connecting-pvc-pipes-to-brass-pipes/
https://www.usplastic.com/knowledgebase/article.aspx?contentkey=803
https://www.doityourself.com/forum/plumbing-piping/338887-removing-pvc-threads-brass-threads.html
https://www.plbg.com/forum/read.php?1,161742
https://www.lawnsite.com/threads/joining-pvc-sch40-to-copper-or-brass.141221/
https://www.linkedin.com/pulse/dos-donts-assembling-threaded-pvc-fittings-larry-workman
https://www.plasticpipeshop.co.uk/Connecting-Metal-Threads-to-Plastic-Threads_b_31.html
https://askinglot.com/can-you-connect-cpvc-to-brass
https://www.linkedin.com/pulse/what-thread-sealant-use-pvc-fittings-larry-workman
https://nastyz28.com/threads/plumbers-sealing-a-threaded-brass-to-cpvc-connection.241478/
https://terrylove.com/forums/index.php?threads/pvc-male-brass-female-coupling.63033/
https://homeguides.sfgate.com/connect-cpvc-brass-shower-valve-84658.html
https://www.lascofittings.com/threads
https://www.answers.com/Q/Can_you_glue_PVC_to_brass
https://www.lawnsite.com/threads/joining-pvc-sch40-to-copper-or-brass.141221/
https://www.amazon.com/GF-Piping-Systems-Transition-Schedule/dp/B00AM6JT2M
https://www.linkedin.com/pulse/dos-donts-assembling-threaded-pvc-fittings-larry-workman
https://www.plasticpipeshop.co.uk/Connecting-Metal-Threads-to-Plastic-Threads_b_31.html