Can You Mix Sram And Shimano Components

More Answers On Can You Mix Sram And Shimano Components

Mixing components – SRAM and Shimano – will it work?

Joined Dec 23, 2003. 3,408 Posts. #10 · Nov 25, 2018. Shimano chains will work with SRAM cassettes, but will not shift as good as if it was shimano/shimano SRAM/SRAM. REason is, Shimano chains use the pins to grab the ramp on the cassette to shift and sram uses the chain plates, which are ramped to grab the cogs.

Technical FAQ: Mixing SRAM and Shimano – VeloNews.com

Mixing SRAM and Shimano. Dear Lennard, I’ve got a full SRAM Rival Hydro disc 1×11 set up on my ’cross bike but want to convert to Shimano shifting — I just find the small SRAM lever too …

Mixing Shimano and Sram? – BikeRadar

Guys, Can I mix sram and shimano components? Never been sure about putting a sram casette with shimano rear mech, or using sram pods with a shimano mech. … allthough you can mix a named Sram Shifter(eg Attack) with a Shimano rear mech, chains front mech and cassete are all fine . Cotic Soul Pearson Hanzo Airborne Zeppelin. 0. Andy B Posts: 8,115.

12 Speed: Mixing SRAM and Shimano Components – Bike Hub

Oct 28, 2021the shifting may feel slower when the chain has a bit of wear on it. Those upshift ramps to the smaller sprockets really does help so IMO the better mixed set up is SRAM derailleur and shimano cassette. Bt if you ride as often as I do then its a cassette per year vs one every 3-4 years with SRAM XO1

Can You Use a SRAM Crankset With Shimano? – Gear For Venture

If you’re looking to replace any components on a 10-speed or 11-speed SRAM bike for those from a Shimano bike, you can rest assured that they’ll work together. Those from other groupsets are not likely to fit together, so make sure you check your bike’s specifications before attempting any modifications. You will be ready to hop back on …

Can you mix and match Sram and Shimano – Singletrack Magazine

Yes, apart from mixing rear shifters and mechs, they usually need to be a matched pair. Yes you can and it works perfectly . The only thing is Sram and Shimano casettes use different freehubs so …

Can I use SRAM chain on Shimano? Thankfully you can!

Mar 12, 2021SRAM and Shimano are two of the most popular bike part brands. Their components are on most bikes that you see both on and offroad. Although each brand will try to tell you that you can only use their components and parts together, there is a lot of interchangeability that can be done. In essence, when SRAM entered the road bike groupset market …

Shimano/SRAM compatibility, new bike, swapping out components

You can’t mix Shimano with SRAM. Until 10s it could work but not no. Now you can’t even mix road and mtb parts from same factory – different pull ratio. If you are going to buy mtb bike you SRAM and Shimano cassette width will be the same – so it can stay after changing shifter and derailleur. In road bike it is different.

Mixing SRAM shifters and Shimano derailleur – BikeRide Forum

Not sure about SRAM trigger shifters, but my hybrid came with SRAM grip shifters and both front and rear deraileurs are Shimano Altus components, including the cassette. … (note: you CAN mix SRAM and Shimano on the front because both pull at the same ratio, it’s just the rear that’s awkward). Wow! I’ve been riding it for 3 months like that!

Are SRAM and Shimano interchangeable? – Quora

Answer (1 of 2): Very difficult to say. They both produce parts that fit the same frames but you may have to change a lot of stuff. Mechs and shifters are not cross-compatible without a cable pull adapter. Cassettes are compatible unless the SRAM bike has a 10t small cog or the Shimano is a 12…

Mixing Shimano and SRAM : bikewrench – reddit.com

Actually, you could keep the front mech and still use Sram shifters, it’s the rear mech that won’t work if you mix Shimano and Sram. 12. Share. Report Save. level 2 · 7y. Cassette & chain ring spacing is the same between the two companies. Campagnolo would differ. You can just switch it out to SRAM if you like (I’m the opposite. I prefer …

Mixing road groupsets: what works together and what doesn’t

There was a time when cyclists were free to mix and match transmission components, but that all changed when Shimano introduced indexed gear shifting in 1984. … the Shimano/SRAM freehub body can …

Mixing SRAM and Shimano – Weight Weenies

by MayhemSWE on Thu Aug 24, 2017 11:46 am. Shimano’s levers pull more brake wire than Sram’s does. Though compatibility is usually still good enough, Shimano brakes paired to Sram levers may require more precise adjustment. charlieboy52000. Posts: 106.

Shimano vs. SRAM: Guide to Groupsets & Drivetrains – The Pro’s Closet

Key points when comparing Shimano and SRAM. – Shimano has been making bike components for 100 years, while SRAM is much younger than it’s Japanese competitor, having opened shop in 1987 in Chicago. – Shimano is more than twice the size of SRAM and dominates original parts spec on road bikes.

Can I Mix and Match Shimano Drivetrain Parts? | Coach Levi

The one thing you do not want to do is mix and match Shimano, SRAM, and Campagnolo together. I consider these manufacturers separate families. You could call Sora, 105, Ultegra, etc. cousins, as they’re all part of the Shimano family and they play well together. The only exception I’ve seen is with a few of the top end components new for 2009.

mountain bike – Can I mix a SRAM Crankset with everything else Shimano …

Probably. It depends on the exact model and specs. My GF’s MTB has SRAM X0 cranks and Truvative chainrings (i.e. SRAM), with Shimano XTR derailleur and Shimano cassette (not sure of the model). All of this is 10 speed – but I believe that it might not work as well with 11 speed.

Mixing SRAM with Shimano….(short term) – CycleChat Cycling Forum

The problem with mixing SRAM and Shimano is with the gears. I forget which way round, but the pull ratio on the shifters isn’t the same. One of them works on a 1:1 ratio, the other is a 1:1.3 (if I remember correctly). 1:1 means that the amount of wire the shifter pulls at the shifter end is exactly the same as the amount that pulls at the derailleur end, the 1:1.3 pulls more.

SRAM components…mix and match? – Road Bike, Cycling Forums

But not much difference other than that and bragging rights. Sram 1090R chain and 1070/1090 cogsets are fine, too. Properly adjusted and lubed, they are just as quiet and quick shifting as Shimano. Dura Ace cogset is lighter, but because of the titanium cogs will cost a lot more and will wear out a whole lot faster.

Can sram work with shimano? – ina.scottexteriors.com

Can you mix and match ultegra with Dura Ace? The key to mixing and matching is making sure you get components from the same generation. For example: 9000 Dura Ace, 6800 Ultegra, and 5800 105 are all cross compatible. Each have 11-speeds in the rear, use the same cable pull per shift and use the same front derailleur design.

Can I mix these SRAM Apex components with Shimano/Ofmega components on …

The pull-rate (cable per click) on SRAM is very different from Shimano. With downtube shifters you could switch to friction mode and use any rear mech. Shimano STI brake lever shifters will not work with SRAM. There are also many variants within Shimano’s ranges over the years that have strange compatibility issues – some useful, others not.

Question: What Are The Pros And Cons Of Sram Bike Components Vs Shimano …

May 30, 2021Can you mix SRAM and Shimano components? SRAM’s cassettes and chains are compatible with all of Shimano’s groupsets, and vice versa. Likewise, Shimano and SRAM buyers have the freedom to mix different levels of chains and cassettes so long as they are designed for the same kind of transmission.

Mixing Shimano and SRAM 11 speed drivetrain components – FAQLoad

With the Shimano 9000 11 speed cassette and groupset having just been recently released, it raises the possibility of mixing and matching Shimano and SRAM 11 speed components. Here’s what seems to be working: XTR M9000 shifter and derailleur working with X01 cassette. If this works, then there is no reason that SRAM 11 speed shifter and derailleur combo should not work with an 11 speed XTR …

Shimano and SRAM Disc Rotors exchangable? – Road Bike, Cycling Forums

1,312 Posts. #8 · May 6, 2019. Generally yes. I have two sets of wheels for my CX bike, which are both Sram rotors, but I swap the wheelsets without messing with the brakes at all. I also straight swapped a set of new Sram rotors in for the stock Shimano rotors on my road bike, no adjustment needed. J.

Technical FAQ: Combining SRAM road and mountain parts

So, do you know if a SRAM mountain derailleur (9-speed XO per say) will work with the Red Shifters and something like an IRD Wide Range 10 Speed cassette (11-34)??

Can you mix Shimano groupsets : bicycletouring – reddit

Shimano, Sram and Campy use different pull ratios for their shifters. Don’t mix and match brands but usually cranks are exempt from this . … The beauty of Shimano is that even the lower tier components work great if taken care of. I’m into 90’s mtbs and you would be surprised how well the cheapest derailleurs still work after 30 years …

Bike Groupsets (Shimano, SRAM, Campagnolo) – Bicycle Guider

Mar 1, 2022Centaur’s shift levers are made from a mix of plastic and carbon fiber and allow multiple upshifts (up to 3 gears). The rear derailleur is compatible with up to 11-32T cassettes, eliminating the need for short and long cage variants. … Shimano’s components can be roughly classified into three groups: entry-level, mid-range, and high-end …

mixing sram and shimano components? — BikeRadar

mixing sram and shimano components? epo-aholic Posts: 1,414. June 2013 edited June 2013 in Road general. Hi guys…. Just a quick one, can i used a sram force front mech with shimano dura ace 7900 sti shifters? I know you can do this on the mtb components but unsure of road compatibility.

12 Speed: Mixing SRAM and Shimano Components – Bike Hub

the shifting may feel slower when the chain has a bit of wear on it. Those upshift ramps to the smaller sprockets really does help so IMO the better mixed set up is SRAM derailleur and shimano cassette. Bt if you ride as often as I do then its a cassette per year vs one every 3-4 years with SRAM XO1

Mixing SRAM with Shimano….(short term) – CycleChat Cycling Forum

The problem with mixing SRAM and Shimano is with the gears. I forget which way round, but the pull ratio on the shifters isn’t the same. One of them works on a 1:1 ratio, the other is a 1:1.3 (if I remember correctly). 1:1 means that the amount of wire the shifter pulls at the shifter end is exactly the same as the amount that pulls at the derailleur end, the 1:1.3 pulls more.

Mixing SRAM and Shimano – Weight Weenies

by MayhemSWE on Thu Aug 24, 2017 11:46 am. Shimano’s levers pull more brake wire than Sram’s does. Though compatibility is usually still good enough, Shimano brakes paired to Sram levers may require more precise adjustment. charlieboy52000. Posts: 106.