A part of the suggested span transcript after expanded is But anyhow this is a speaker wire antenna. And these things seem to have gained some popularity. Because. They're very cheap. And simple to make and then one of the benefits.
Just be aware that speaker wire has a tendency to stretch over time so it after a while you might have to climb back up there and clip some of the ends off. You can use speaker wire, but be aware that how you hang it and the type of antenna you build can lead to problems.
I have used speaker wire but always split the pairs. I tend to unroll the speaker wire to the desired length, cut and then pull the two wires apart leaving me two perfect halves for the dipole.
It’s perfectly fine. Just be aware that speaker wire has a tendency to stretch over time so it after a while you might have to climb back up there and clip some of the ends off.
Can any wire be used as an antenna?
Since most antennas are used outdoors, you must use outdoor-rated wire. You can use uninsulated wire, but it is much better to use insulated wire for safety purposes if there is any chance that someone could come in contact with the wire while you are transmitting.
Is speaker wire good for FM antenna?
Originally Answered: Can I make an FM antenna from a speaker wire? Yes. It will work best if it is 75 centimeters long because there is a direct correlation between the wavelength and the antenna element length.
Can I use speaker wire for signal?
You can definitely use speaker wire for 12v power. The only factor to consider is the wire gauge. Various gauges will allow for higher or lower amperage, which, when multiplied with volts (in our case 12v), will give you the electrical load (watts) that the electrical device or appliance should be.
Can a speaker act as an antenna?
Yes, the speaker wires are acting as antennas. This is very common. Buy some ferrite rings (doughnut shapes) about 1.5″ across. Disconnect a speaker wire at the amplifier end, loop it through a ring as many times as you can (fill the ring up without overlapping windings), then reconnect the wire.
Can you use speaker wire for antenna wire?
Since most antennas are used outdoors, you must use outdoor-rated wire. You can use uninsulated wire, but it is much better to use insulated wire for safety purposes if there is any chance that someone could come in contact with the wire while you are transmitting.
How do you make an antenna with speaker wire?
Originally Answered: Can I make an FM antenna from a speaker wire? Yes. It will work best if it is 75 centimeters long because there is a direct correlation between the wavelength and the antenna element length.
How do you make an antenna out of speaker wire?
Since most antennas are used outdoors, you must use outdoor-rated wire. You can use uninsulated wire, but it is much better to use insulated wire for safety purposes if there is any chance that someone could come in contact with the wire while you are transmitting.
How do you make an FM antenna out of copper wire?
With copper being twice as conductive as aluminum and 6 times more conductive than steel, it makes an excellent choice as an antenna material. The increased electrical efficiency means more of your RF energy will go up and out the antenna and not be trapped, creating heat energy.
How can I make my antenna more powerful?
Aluminium. Lightweight and cheap, aluminium is one of the best materials with which to make a television antenna. Aluminium can be used in the form of foil, a thin sheet of reflective and flexible metal, or as sturdier mesh allowing debris to fall through.
What is the best material to make an antenna?
After a year in the making, we are truly thrilled to unveil our latest creation—the all-new DB8e! From its superior signal strength to its ability to target multiple towers from any direction—the DB8e is truly a one of a kind antenna.
How long can a coaxial cable be for a TV antenna?
The maximum extension that may be added to the standard length of cable supplied with an antenna is 10 meters. Extensions are available in standard lengths of 5 and 10 meters. Longer extensions are possible, but such an extension must be installed by a qualified technician.
How can I make a homemade antenna for my TV?
You can make your own digital TV antenna for watching television channels without having to pay for the service, such as from a cable or satellite service provider. You will need a few supplies, including a length of coaxial cable long enough to reach from outside your home to the TV.
More Answers On Can I Use Speaker Wire For Antenna
Can a speaker wire be used for a radio antenna? – Quora
In theory, every metal can be used as antenna with varying results. In order to achieve maximum signal strenght in FM band, opt for a lenght of 28 inches ~ (72 cm) of speaker cable (both strings), split it to create a dipole antenna and connect the wires to the “balanced” input of the tuner. Some will claim impedance mismatch – they would be right.
How To Make An FM Antenna From A Speaker Wire?
Apr 25, 2021You can try another method to make an FM antenna with the speaker wire. For this purpose, you need a wire of about 6 to 7 feet in length. It is always advisable to take more than the necessary wire so that you do not run out of wire during the process. The next step is stripping the wires of the antenna and the speaker wires.
Can I use speaker wire as an FM antenna? – Answers Log
Jun 21, 2022Yes, you can easily use the speaker wire as an FM antenna. Is speaker wire good for an antenna? Speaker wire (or ordinary lamp cord) makes an excellently balanced feedline for HF radio with a characteristic impedance of around 75 ohms. It’s perfect for feeding HF dipoles. Can any wire be used as an antenna?
Can you use speaker wire for a radio antenna? – Malariafacts
Originally Answered: Can I make an FM antenna from a speaker wire? Yes. It will work best if it is 75 centimeters long because there is a direct correlation between the wavelength and the antenna element length. Do ham radio licenses expire? Licenses currently remain valid for 10 years from the date of issuance or renewal. Renewal can be done …
How To Make An FM Antenna From Speaker Wire (Step-by-Step)
Jun 3, 2022To construct an FM radio antenna from speaker wire, first get a 10-foot dual speaker wire and measure out 3 feet. Next, split the speaker wire at the 3-foot mark and craft a large “T” for each 3-foot length of dual speaker wire. The T-shaped wire should be placed perpendicularly to the rest of the intact wire.
How To Make An FM Antenna From Speaker Wire In 2022
Feb 21, 2022Connect the speaker wire to the Receiver On the back of the receiver, look for the external antenna connector. It may be referred to as “ext. ant” or “ant.” Wrap each of the two speaker cable cables around the external antennae connecting posts. Clamp and hold if the connection is a clamp-and-hold mechanism.
antenna made with speaker wire : amateurradio – reddit
You can use speaker wire, but be aware that how you hang it and the type of antenna you build can lead to problems. If the wire includes a couple of steel strands in it you’re in good shape for antennas. If it’s only copper and you hang it by the ends (and pull them tight) you will lengthen the antenna over time!
speaker wire antennas – WB3GCK QRP Amateur Radio
Speaker Wire End-Fed Half-Square Antenna Materials Here’s what I used to build it: 50 feet of two-conductor speaker wire (1) Spade lug (4) small zip ties Goop® sealant/adhesive (or similar) Construction Refer to the accompanying diagram to help make sense of the following steps. Separate the speaker wire into two 50-ft wires
How to make a Ham Radio Speaker Wire Antenna. Post #1470.
In this video from KG6HQD, we learn how an antenna designed for SOTA operations (Summits On The Air) evolved into a simple, practical, and inexpensive HF antenna for both home and field use. Although the speaker wire antenna was designed for the 20 meter band, KG6HQD says his new Elecraft KX2 can work stations from 40 through 10 meters “with ease.”
Good wire for wire antenna? – Amateur Radio Stack Exchange
In any place were the National Electric Code (NEC), that is used in much of the United States, is enforced as law the minimum size of wire that can be used for an amateur radio transmitting antenna is number fourteen American Wire Gauge (14AWG). For people in other parts of the world that is equivalent to 1.63mm diameter or 2.08 square mm.
Speaker Wire Half-Square Antenna – WB3GCK QRP Amateur Radio
Jun 12, 2020Speaker Wire End-Fed Half-Square Antenna Materials Here’s what I used to build it: 50 feet of two-conductor speaker wire (1) Spade lug (4) small zip ties Goop® sealant/adhesive (or similar) Construction Refer to the accompanying diagram to help make sense of the following steps. Separate the speaker wire into two 50-ft wires
Using Speaker Wire as an Antenna to receive 20 and 40 meter bands …
The speaker wire should work just fine as a listening antenna. What’s your noise level on your S-meter. I bet you have a lot of RFI. When I was listening only, I didn’t have great luck with my wire antenna until I picked up a cheap antenna tuner from a local ham. The difference is pretty amazing even for just listening.
How To Improve FM Signal on Radio with A Single Wire Antenna
May 5, 2022The following components are needed to make an FM antenna using speaker wire. Speaker wire of at least 1200 inches; An FM receiver with a proper clamp fixing arrangement; General wire strippers. Steps of How To Improve FM Signal on Radio with A Single Wire Antenna. 01. First, the speaker wire of around three feet is torn. Now take a cutting …
How to construct a multi-band dipole using speaker wire – Ham Blog
20m – 10.06 meters of wire. 17m – 7.88 meters of wire. 15m – 6.72 meters of wire. To calculate the length of wire for other frequencies you can use this formula: Total length (in meters) = 142.65/ƒ. For example if we wanted to add the 12m band (24.940MHz), we’d do the following: Total length (in meters) = 142.65/24.940.
Best Wire for Dipole Antenna in 2021 – Antenna Fix
Aug 25, 2020The go-to best wire for dipole antenna people. RG8X Coaxial cable is the best selling in the market with ULF (PL-259) plugs. It comes with 50-ohm impedance and the cable is approximately 0.25 inches thick. The item weighs around 2.97 pounds which makes it easy to carry and has dimensions of 10.91 inches x 9.25 inches x 2.95 inches.
How to Boost Your TV Antenna Signal and Get Better Reception – Tom’s Guide
In general, the higher you place your antenna, the better. It would be best to have your antenna placed 30 feet above ground level to give you the clearest over-the-air connection with a tower …
Antenna Jobs, Employment in Los Angeles, CA | Indeed.com
238 Antenna jobs available in Los Angeles, CA on Indeed.com. Apply to Engineer, Call Center Representative, Construction Laborer and more!
Can a speaker wire be used for a radio antenna? – Quora
Answer (1 of 13): Definately yes. In theory, every metal can be used as antenna with varying results. In order to achieve maximum signal strenght in FM band, opt for a lenght of 28 inches ~(72 cm) of speaker cable (both strings), split it to create a dipole antenna and connect the wires to the “b…
Can you use speaker wire for a radio antenna? – Malariafacts
Originally Answered: Can I make an FM antenna from a speaker wire? Yes. It will work best if it is 75 centimeters long because there is a direct correlation between the wavelength and the antenna element length. Do ham radio licenses expire? Licenses currently remain valid for 10 years from the date of issuance or renewal. Renewal can be done …
Can you make a AM antenna out of speaker wire?
I am thinking of getting a 100’ of speaker wire and run it all around my attic for my AM antenna. Something happened to my other antenna and it is not working very well. any more.
Ideas for an antenna made of speaker wire cable : RTLSDR
I suggest using an antenna tuner built for the HF bands. The simplest is the ( L tuner). It will have the advantage in tuning a long wire in most circumstances.. This type of tuner can also give some band filtering. It is superior to the 9 to1 balun. And can be used with the 9 to 1 balun to extend the tuner range.
How To Improve FM Signal on Radio with A Single Wire Antenna
The following components are needed to make an FM antenna using speaker wire. Speaker wire of at least 1200 inches; An FM receiver with a proper clamp fixing arrangement; General wire strippers. Steps of How To Improve FM Signal on Radio with A Single Wire Antenna. 01. First, the speaker wire of around three feet is torn. Now take a cutting …
How to Make an FM Antenna (with Pictures) – wikiHow
To make an FM antenna using speaker wire, start by splitting 3 feet of wire and arranging it to form a “T” shape. Next, strip the bottom 2 inches of insulation from the wire. Then, connect the exposed wires at the bottom of the “T” shape to the FM connections. Finally, place your antenna as high up and as close to the nearest station as …
DIY (FM Antenna) Speaker Wire Recipe – Blogger
Only the Monster’s were better. The Monster wire, as compared to the FM antenna wire, had a fuller, fatter, perhaps larger sound. So more body on instruments and such. However, it was slower on transients than the FM/speaker wire combo. The antenna wire combo had a more liquid-y midrange (“liquid” is good), and a thinner, but quicker sound.
Speaker wire/bell wire? – DoItYourself.com Community Forums
Are you using this wire for an antenna or a speaker extension? For an antanna, just get one of those T shaped FM Diplole antennas, which are often made from twinlead. For speaker wire on a small stereo system bell wire can work, but it is easier to use speaker wire. Bell wire is solid copper, typically a twisted pair, and either 22 or 24 awg.
Good wire for wire antenna? – Amateur Radio Stack Exchange
In any place were the National Electric Code (NEC), that is used in much of the United States, is enforced as law the minimum size of wire that can be used for an amateur radio transmitting antenna is number fourteen American Wire Gauge (14AWG). For people in other parts of the world that is equivalent to 1.63mm diameter or 2.08 square mm.
Field Report: Let’s build a super simple antenna on-site and activate …
Here’s how I prepared the antenna: First, I cut 28.5 feet of the speaker wire from the roll and split the paired wires so that I’d have two full 28.5 foot lengths. Next, I stripped the ends of the wire and attached banana jacks I found in my junk drawer. Although these aren’t necessary as the binding post adapter can pair directly with …
Best Wire for Dipole Antenna in 2021 – Antenna Fix
The go-to best wire for dipole antenna people. RG8X Coaxial cable is the best selling in the market with ULF (PL-259) plugs. It comes with 50-ohm impedance and the cable is approximately 0.25 inches thick. The item weighs around 2.97 pounds which makes it easy to carry and has dimensions of 10.91 inches x 9.25 inches x 2.95 inches.
How to Make a Ham Radio Speaker Wire Antenna. Post #1596.
If you need a simple, efficient, cheap, and lightweight antenna for portable or field operations, the “HQD” Speaker Wire Antenna from Jerry (KG6HQD) may be the answer. The antenna resembles several designs featured in past editions of the “ARRL Antenna Book.” Those examples used commonly available “zip cord” available at many hardware and home …
Can I use speaker wire as a transmission line?
You’ll have to estimate the dialectric constant. Speaker wire makes a fine transmission line if you split it and make ladder line from it. Though, I can’t help but think that If speaker wire as-is was a Good Enough transmission line, cheap hams would already be using it. – John VE3WNA. 14 hours ago.
Resource
https://www.quora.com/Can-a-speaker-wire-be-used-for-a-radio-antenna?share=1
https://www.kaccradio.com/how-to-make-an-fm-antenna-from-a-speaker-wire/
https://answerslog.com/can-i-use-speaker-wire-as-an-fm-antenna/
https://malariafacts.com/entertaiment/can-you-use-speaker-wire-for-a-radio-antenna/
https://www.seriftv.com/how-to-make-an-fm-antenna-from-speaker-wire/
https://drscott.com/how-to-make-an-fm-antenna-from-speaker-wire/
https://www.reddit.com/r/amateurradio/comments/3s16e7/antenna_made_with_speaker_wire/
https://wb3gck.com/tag/speaker-wire-antennas/
https://www.simplehamradioantennas.com/2018/04/how-to-make-ham-radio-speaker-wire.html
https://ham.stackexchange.com/questions/140/good-wire-for-wire-antenna
https://wb3gck.com/2020/06/12/speaker-wire-half-square-antenna/
https://www.reddit.com/r/amateurradio/comments/ckl5z2/using_speaker_wire_as_an_antenna_to_receive_20/
https://www.radio4all.org/how-to-improve-fm-signal-on-radio-with-a-single-wire-antenna/
http://www.hamblog.co.uk/how-to-construct-a-multi-band-dipole-using-speaker-wire/
https://antennafix.com/best-wire-for-dipole-antenna/
https://www.tomsguide.com/us/get-better-tv-antenna-reception,review-4064.html
https://www.indeed.com/q-Antenna-l-Los-Angeles,-CA-jobs.html
https://www.quora.com/Can-a-speaker-wire-be-used-for-a-radio-antenna?share=1
https://malariafacts.com/entertaiment/can-you-use-speaker-wire-for-a-radio-antenna/
https://www.radiodiscussions.com/threads/can-you-make-a-am-antenna-out-of-speaker-wire.605341/
https://www.reddit.com/r/RTLSDR/comments/6mfh3w/ideas_for_an_antenna_made_of_speaker_wire_cable/
https://www.radio4all.org/how-to-improve-fm-signal-on-radio-with-a-single-wire-antenna/
https://www.wikihow.com/Make-an-FM-Antenna
https://theadvancedaudiophile.blogspot.com/2011/07/diy-fm-antenna-speaker-wire-recipe.html
https://www.doityourself.com/forum/electrical-ac-dc/284753-speaker-wire-bell-wire.html
https://ham.stackexchange.com/questions/140/good-wire-for-wire-antenna
https://qrper.com/2021/06/field-report-lets-build-a-super-simple-antenna-on-site-and-activate-this-park/
https://antennafix.com/best-wire-for-dipole-antenna/
https://www.simplehamradioantennas.com/2018/08/how-to-make-ham-radio-speaker-wire.html
https://ham.stackexchange.com/questions/20939/can-i-use-speaker-wire-as-a-transmission-line