Skip to content

Can I Plane End Grain

A part of the suggested span transcript after expanded is I should I will I send it through a planer. In order to flatten it out and the answer right off the bat is no don't do it here's. The reason. And grain cutting board means.

In Western woodworking at least low-angle block planes are favoured for planing end grain. These will generally give the best result, but any plane can do it if the iron is sharp enough and you take a very light cut.

If you’re having trouble cleanly planing the end grain of a board with a traditional bench plane (either in the vise or on the shooting board), the problem isn’t the cutting angle of the plane. The culprit is the blade. The only secret – if you can call it that – to planing end grain is a sharp blade.

The culprit is the blade. The only secret – if you can call it that – to planing end grain is a sharp blade. The size of the plane’s mouth is irrelevant.

Can a planer be used on end grain?

In general, planing the end grain is discouraged because it can cause catastrophic tear-outs which can break the cutting board into pieces and also damage the planer machine, in addition to being a safety hazard for the user.

How do you Plain end grains?

If you’re having trouble cleanly planing the end grain of a board with a traditional bench plane (either in the vise or on the shooting board), the problem isn’t the cutting angle of the plane. The culprit is the blade. The only secret – if you can call it that – to planing end grain is a sharp blade.

Why is end grain difficult to plane?

In Western woodworking at least low-angle block planes are favoured for planing end grain. These will generally give the best result, but any plane can do it if the iron is sharp enough and you take a very light cut.

Can you plane a end grain cutting board?

In general, planing the end grain is discouraged because it can cause catastrophic tear-outs which can break the cutting board into pieces and also damage the planer machine, in addition to being a safety hazard for the user.

Can I use a hand plane on end grain?

In Western woodworking at least low-angle block planes are favoured for planing end grain. These will generally give the best result, but any plane can do it if the iron is sharp enough and you take a very light cut.

What hand plane is best for end grain?

I had this idea that I would be able to run the hand plane over the surface of the (already smooth) cutting board and peel off whisper-thin shavings. Yes that is exactly what you should be able to do so don’t despair you haven’t bought into something that isn’t going to deliver what you want.

Can you run a plastic cutting board through a planer?

Acrylic plastics will be probably destroyed – broken -, Polycarbonate (PC) may damage the planer. PC is ductile, there is not much chip breaking. The bit in the middle will not damage the materials. If you are desperate you can drill a hole into PC by using a masonry bit.

Can hand planes end grain?

In general, planing the end grain is discouraged because it can cause catastrophic tear-outs which can break the cutting board into pieces and also damage the planer machine, in addition to being a safety hazard for the user.

Can you plane a cutting board?

In general, planing the end grain is discouraged because it can cause catastrophic tear-outs which can break the cutting board into pieces and also damage the planer machine, in addition to being a safety hazard for the user.

How do you smooth out a plastic cutting board?

To restore a cutting board, a 150-180 grit sanding will be necessary to remove as much knife marks as possible. If the surface is too damaged or that the marks are too deep, you can use a more aggressive paper (100-120 grit) with a sanding machine. Remove dust the surface and make sure the board is clean.

How do I make my plastic cutting board white again?

First, soak the board in a white vinegar solution or spray it with a 3% hydrogen peroxide solution. (Either way, let the board sit for at least five minutes before washing it again with soap and water.) Then, make a paste that’s one part baking soda, one part salt, and one part water to scrub out surface stains.

How do you recoat a cutting board?

Starting with 80-grit sandpaper, sand the cutting board along the grain to remove deep cuts and dents. Wipe with a damp cloth, and let dry completely before repeating with 120-grit and finally 220-grit sandpaper. The cutting board should feel quite smooth at this point and will be much lighter in color.

More Answers On Can I Plane End Grain

End-grain Through the Planer? Bad Idea! – The Wood Whisperer

What does the Wood Whisperer think about running end-grain through the planer? Im SOOOOOOOO tempted to try it because it would be so easy to clear up some high spots, but Ive read that this can cause serious kickback, possibly turning the planer into a large grenade. (At least my portable anyway).

How To plane end grain – Wallybois – Woodworkers Journal

Plane the end grain with a sharp low angle block plane. How does it work? The Urea Formadahide Cascamite bonds the pores and fibres of the timber to be planed. This prevents the fibres from breaking away from the timber. The Cascamite also hardens the wood. The concept works similar to applying masking tape to a cute line to prevent break out.

Can you plane end grain cutting board ? – MellowPine

May 16, 2022You can plane an end grain cutting board but it would be inadvisable especially if you are inexperienced. In general, planing the end grain is discouraged because it can cause catastrophic tear-outs which can break the cutting board into pieces and also damage the planer machine, in addition to being a safety hazard for the user.

How do you plane end grain? – Woodworking Stack Exchange

In Western woodworking at least low-angle block planes are favoured for planing end grain. These will generally give the best result, but any plane can do it if the iron is sharp enough and you take a very light cut. Terminology note: a plane’s blade is traditionally referred to as an iron, in older books sometimes as the cutter.

Secret to planing end grain? | Popular Woodworking

What you need to plane end grain is a SHARP plane. If that’s your block plane, use that. If I had to come up with a secret I’d say I prefer to plane end grain with a plane that has a cambered iron. That way I can square up a hand-sawn end the same way you square an edge with a try plane. — Adam Cherubini Product Recommendations

cannot seem to plane end-grain – Hand Tools – Wood Talk Online

Planing end grain can be difficult, as you have discovered. From the first picture you posted, it looks like the angle between the plane blade and the wood is about 45 degrees. This is about right for general purpose use, but not so good for end grain. For end grain, it is better if the angle is smaller, as I have shown in the second picture below.

How to plane against the grain without tear-outs – Quora

Its a difficult one, some woods have interlocking grain. One thing to try first is to adjust the frog of the jack plane forward until the front lip of the mouth is very close to the cutting edge and take very fine shavings also working diagonally to the grain instead of along it. If it still tears out use a scraper plane instead.

Can/Should I run end grain through my DW733 planer?

Im new to this.. and this dosent seem like a good idea.. I have seen references in videos to ’only plane with the grain’. I just read through the manual 5x, and I dont see anything about it in there. The project is (of course) a cutting board.. so can I do this? Or is this strictly a sanding/hand plane thing?

End-Grain through the Planer? Just Don’t! – The Geek Pub

Cutting end-grain is much tougher on your blades. If you send end-grain through the planer it stands a very likely chance of the board fracturing and your planer ejecting the board and very high materials. This is an extremely dangerous situation that you do no want to be around when it goes off. My Personal Story with End-Grain through the Planer

Planing End Grain – Bob Rozaieski Fine Woodworking

The only secret – if you can call it that – to planing end grain is a sharp blade. The size of the plane’s mouth is irrelevant. The chipbreaker position doesn’t even matter. What matters is that the blade is sharp. Not kind of sharp, but as sharp as you can get it. Ultimately, you should use whatever planes you want.

running end grain through my planer | Woodworking Talk

5,531 Posts. #6 · Oct 7, 2015. Sure, you can feed an end grain board through a planer. Once. Tried it myself, launched a 13×18 solic maple board about 10 feet across my shop. Would gone further if it didn’t ping off a wall. S.

Planing end grain – a little experiment – Woodwork Forums

I would say that one should get the adjustable mouth, but because it is useful for planing interlinked face grain rather than as a specialized plane for end grain. So as a test I chose two pieces of timber, one Scandinavian pine and the other American Cherry. The plane used was my Stanley #65 block plane, which has a low cutting angle and an …

Can I Plane end grain?

Can I Plane end grain? 4 Answers. In Western woodworking at least low-angle block planes are favoured for planing end grain. These will generally give the best result, but any plane can do it if the iron is sharp enough and you take a very light cut. Yes, tearout of the long grain at the edge of the board is always a concern. About Us Trending

Using a power planer on end grain surfaces – successfully

Apr 18, 2021This next video shows cutting the panel pieces. After cutting these pieces the panels will be glued together and orientation will be looked at for a pattern or for randomization. Now that we have panels made, the planer is next. I added (off camera) a pine end board that is cross grain glued to the panel. Doing this and leaving the board there …

10 Tips for Working With End Grain | Popular Woodworking

First, try to plane from both outside edges of the door and stop in the middle of the rail. This method works well when the grain of the rail runs fairly straight. If the rail has a very pronounced grain direction, and planing against the grain produces tearout, go to Plan B: the backer board. Clamp a small block flush with the stile.

Plane end grain troubles – Woodworking Masterclasses

By the way, yes, end grain on short pieces is tricky (to orient and stabilize the plane) 4 May 2017 at 3:35 pm #311696 Joris Kempen Participant thanks for the tips. regarding sharpening; i go from the diamond plates from coarse fine super fine and feel a burr on the flat face.

How Do You Plane End Grain? – Wood Goal

Apr 21, 2022Step 7. Repeat steps 4 to 6 until getting the desirable conditions. We should warn you. If you use wet or fresh wood to plane end grain, it may peel off and ruin your whole work; therefore, it’s best to let the wood dry and then attempt to plane it. Now that we exactly know how to plane end grain, it’s time to read some tips and methods …

Do Moulding Planes Mould End Grain? – Paul Sellers’ Blog

Obviously you cannot plane through-cuts without back up on endgrain profiling in much the same way you can’t always have free cuts on moulding machines such as spindle shapers and routers. I usually clamp a continuing section of wood to carry the plane through and prevent the speltching (blowout US) as shown.

Hand Planing End Grain | uWoodcraft.com

Planing End Grain with a Jack Plane Make sure that the plane iron is very sharp and that the plane iron cap is set very close to the cutting edge, not over 1/32 of an inch. Lock the stock firmly in the vise with the end protruding slightly. In planing end grain, it is not possible to go completely across the end, as this will split out the wood.

Running an End Grain Cutting Board in a Planer? | WWGOA

2 days agoEnd grain cutting boards start out as a standard panel-type glue up, with the boards glued edge to edge, long grain up. Once the glue is dry on that panel it gets flattened (it’s OK to use a planer at this stage), the panel is crosscut into a number of pieces, and each strip is stood up on end. This new assembly is glued together resulting in …

Using a power planer on end grain surfaces – successfully

This next video shows cutting the panel pieces. After cutting these pieces the panels will be glued together and orientation will be looked at for a pattern or for randomization. Now that we have panels made, the planer is next. I added (off camera) a pine end board that is cross grain glued to the panel. Doing this and leaving the board there …

Running an End Grain Cutting Board in a Planer? | WWGOA

End grain cutting boards start out as a standard panel-type glue up, with the boards glued edge to edge, long grain up. Once the glue is dry on that panel it gets flattened (it’s OK to use a planer at this stage), the panel is crosscut into a number of pieces, and each strip is stood up on end. This new assembly is glued together resulting in …

Planing End Grain | Wood And Shop

You can then chamfer along the edges with a block plane – or whatever you have available – down to that line. Then plane the middle (the portion of end grain that remains “above” your line) until it is flat across the end grain face. I hope that makes sense…. It’s the slickest way I’ve seen to plane a long piece of end grain …

Can you really plane an end-grain cutting board?

I’m working on an end grain cutting board, and the board needs some planing. I don’t really want to sand it, so I figured I’ll just plane it using my benchtop planer. But my friend who’s a carpenter said it’s not good to plane it. Now, I’m confused. Can anyone help me understand why that is?

10 Tips for Working With End Grain | Popular Woodworking

First, try to plane from both outside edges of the door and stop in the middle of the rail. This method works well when the grain of the rail runs fairly straight. If the rail has a very pronounced grain direction, and planing against the grain produces tearout, go to Plan B: the backer board. Clamp a small block flush with the stile.

cannot seem to plane end-grain – Hand Tools – Wood Talk Online

Planing end grain can be difficult, as you have discovered. From the first picture you posted, it looks like the angle between the plane blade and the wood is about 45 degrees. This is about right for general purpose use, but not so good for end grain. For end grain, it is better if the angle is smaller, as I have shown in the second picture below. Skewing the plane as Onboard suggested makes …

Planing end grain cutting board – by DuaneEDMD @ LumberJocks.com …

Planing end grain cutting board. The current project I am working on is an end grain style cutting board that will sit on top of my cook-top and cover the griddle when it is not in use. The board is 12″ wide and 22″ long and was 1.5″ thick. I glued up my blanks, cut them, rotated them to expose the end grain and glued again.

Planing an end grain cutting board – The Patriot Woodworker

If you want to stick to the hand plane approach, generally the lower angle planes are considered better for the end grain. One of the bevel up planes should work well. Note that I am hardly a hand tool guru, and certainly not a hand plane guru, Steven may be along with some more input. But if you consider getting a bevel up plane (also called a low angle plane) the new ones can be expensive …

Can I just plane this? : woodworking – reddit.com

OP are you trying to plane the end grain or edge grain? If end grain, as other posters have said, beware, you’ll most likely have some detrimental results to your piece. Some success can be achieved by putting a 45 degree chamfer on the end that passes through the planer last. Still, Risky business. If you’re meaning the edge grain …

Screw in end grain – Wood design and engineering – Eng-Tips

As you know by now screwing into end grain is not a good idea , however when you absolutely have to do it, I have had good results by pilot drilling the holes , then using a screw 4 times the length of a screw you would use for cross grain to compensate for the poor holding power i.e. cross grain 2″ long end grain 8″ long . remember for a 3/8″ lag screw you will have a withdrawal force of …

Resource

https://thewoodwhisperer.com/articles/end-grain-through-the-planer/
https://www.wallybois.com/how-to-hand-plane-end-grain/
https://mellowpine.com/blog/can-you-plane-end-grain-cutting-board/
https://woodworking.stackexchange.com/questions/741/how-do-you-plane-end-grain
https://www.popularwoodworking.com/editors-blog/secret-to-planing-end-grain/
https://www.woodtalkonline.com/topic/4812-cannot-seem-to-plane-end-grain/
https://www.quora.com/How-do-I-plane-against-the-grain-without-tear-outs?share=1
https://www.reddit.com/r/woodworking/comments/2ms99x/canshould_i_run_end_grain_through_my_dw733_planer/
https://www.thegeekpub.com/3735/end-grain-through-the-planer-just-dont/
https://brfinewoodworking.com/planing-end-grain/
https://www.woodworkingtalk.com/threads/running-end-grain-through-my-planer.109713/
https://www.woodworkforums.com/f152/planing-grain-little-experiment-18292
https://mikra.scottexteriors.com/can-i-plane-end-grain
https://cooperspens.com/using-a-power-planer-on-end-grain-surfaces-successfully/
https://www.popularwoodworking.com/techniques/10-tips-for-working-with-end-grain/
https://woodworkingmasterclasses.com/discussions/topic/plane-end-grain-troubles/
https://woodgoal.com/how-do-you-plane-end-grain/
https://paulsellers.com/2014/11/do-moulding-planes-mould-end-grain/
https://uwoodcraft.com/hand-planing-end-grain/
https://www.wwgoa.com/video/running-end-grain-cutting-board-planer/
https://cooperspens.com/using-a-power-planer-on-end-grain-surfaces-successfully/
https://www.wwgoa.com/video/running-end-grain-cutting-board-planer/
https://forum.woodandshop.com/forum/topic/planing-end-grain/
https://www.reddit.com/r/BeginnerWoodWorking/comments/jd0swq/can_you_really_plane_an_endgrain_cutting_board/
https://www.popularwoodworking.com/techniques/10-tips-for-working-with-end-grain/
https://www.woodtalkonline.com/topic/4812-cannot-seem-to-plane-end-grain/
https://www.lumberjocks.com/DuaneEDMD/blog/8839
https://thepatriotwoodworker.com/forums/topic/16089-planing-an-end-grain-cutting-board/
https://www.reddit.com/r/woodworking/comments/stfiog/can_i_just_plane_this/
https://www.eng-tips.com/viewthread.cfm?qid=449505